Vacuum Bagging Supplies

High tack sealant tape that is wider and thicker than our AT-199. Excellent clean up. Roll size is 1/8" x 1/2" x 25 ft. (3.2mm x 12.7mm x 7.62m)

A tight weave all white polyester peel ply to texture the laminate surface, avoiding sanding or abrading as a surface prep for painting or bonding....

Resinflow 60 is designed to assist resin flow through your part during the VARTM (Vacuum Assisted Resin Transfer Moulding) process. This material i...

Nylon film, resistant to polyesters, epoxies and vinylester with excellent elongation and strength for contours. .0015 x 60" x 1000 ft. SHIPPING AN...

This perforated release film provides excellent release from polyesters, vinylesters, and epoxies. 285°F (140°C) The small hole perforations allow ...

Lightweight breather that allows you to pull "full" vacuum and remove volatiles without vacuum trap off that can warp laminates. 60" x 100 yards   ...

A heavier version of our Econo Ply J, used when extra strength is needed for removal. An excellent texture to the laminate surface is acheived, avo...

Polyethylene Tubing is used to connect the vacuum reservoir to the part to be infused. Available with a 1/2" O.D. and a 3/8" I.D. for use with 3/8"...

Enkachannel for resin infusionEnka-Channel is a 50 mm wide, 4 mm thick, supply or feeder channel for VARTM, consisting of a black three-dimensional...

Enka-Channel is a 100 mm wide, 4 mm thick, supply or feeder channel for VARTM, consisting of a black three-dimensional polyester filament core stru...

Stretchlon 200 is green in color with a 250° F maximum temperature usage. Stretchlon 200 is ideal because it is able to stretch to compress every a...

inexpensive polyethylene parts, used to connect the vacuum manifold and resin feed lines for low temperature resin infusion projects. RIC 12 is use...

This release film provides excellent release from polyesters, vinylesters, and epoxies. 285°F (140°C) Good elongation and conformability. .001" x 6...

Designed to provide accurate, controlled vacuum that you can see and adjust. 1/4" NPT fittings

Nylon film, resistant to polyesters, epoxies and vinylester with excellent elongation and strength for contours. .0015 x 60/120" c fold x 500 ft. S...

Econostitch® is a non-coated nylon peel ply fabric with red tracers which make this peel ply more visible before and after cure, reducing the possi...

Econotac 2 is an economical rubber based contact spray adhesive, designed for temporary bonding applications.Econotac 2 can be used to hold dry f...

WL6400 is a heat-stabilised nylon film suitable for cure temperatures up to 204 °C Material type Nylon ...

A complete starter vacuum bagging kit for room temperature repairs and small laminating projects up to 13 sq ft. Some item specifications may vary....

AirTech Spiral Wrap air duct infusion hose is used to allow air, and eventually excess resin, to be pulled from the perimeter of a molded product. ...

Used to connect polyethylene tubing and/or spiral wrap together, to make your network of vacuum infusion lines to the laminate. "Barbed" ends enabl...

Used to connect polyethylene tubing and/or spiral wrap together, to make your network of vacuum infusion lines to the laminate. "Barbed" ends enabl...

Used to connect polyethylene tubing and/or spiral wrap together, to make your network of vacuum infusion lines to the laminate. "Barbed" ends enabl...

A "venturi" type of a valve that allows you to generate a vacuum from a positive pressure air line. Less expensive than a vacuum pump. Data sheet c...