AIRTECH INTERNATIONAL

Multi-purpose vacuum bag sealant tape that will seal easily to our vacuum bags and your mold. Clean up is simple. 1/16" x 3/8" x 50 ft. per roll (1...

Airtac 2 MEGA is a spray rubber adhesive designed for temporary bonds. Airtac 2 MEGA can be used on materials needing extra tack for placement on v...

High tack sealant tape that is wider and thicker than our AT-199. Excellent clean up. Roll size is 1/8" x 1/2" x 25 ft. (3.2mm x 12.7mm x 7.62m)

This release film provides excellent release from polyesters, vinylesters, and epoxies. 285°F (140°C) Good elongation and conformability. .001" x 6...

This perforated release film provides excellent release from polyesters, vinylesters, and epoxies. 285°F (140°C) The small hole perforations allow ...

Econostitch® is a non-coated nylon peel ply fabric with red tracers which make this peel ply more visible before and after cure, reducing the possi...

Nylon film, resistant to polyesters, epoxies and vinylester with excellent elongation and strength for contours. .0015 x 60" x 1000 ft. SHIPPING AN...

Nylon film, resistant to polyesters, epoxies and vinylester with excellent elongation and strength for contours. .0015 x 60/120" c fold x 500 ft. S...

A tight weave all white polyester peel ply to texture the laminate surface, avoiding sanding or abrading as a surface prep for painting or bonding....

A heavier version of our Econo Ply J, used when extra strength is needed for removal. An excellent texture to the laminate surface is acheived, avo...

Econotac 2 is an economical rubber based contact spray adhesive, designed for temporary bonding applications.Econotac 2 can be used to hold dry f...

Lightweight breather that allows you to pull "full" vacuum and remove volatiles without vacuum trap off that can warp laminates. 60" x 100 yards   ...

1/4" NPT Thread Fittings (female)   For additional information, click here.

inexpensive polyethylene parts, used to connect the vacuum manifold and resin feed lines for low temperature resin infusion projects. RIC 12 is use...

Safelease® 30 is a non-silicone waterbased PTFE release liquid. It will release any laminate from any type of mold surface and will withstand tempe...

A negative pressure gauge that allows you to see how much vacuum pressure is actually on your laminate and if your vacuum bag is sealed or leaking....

Designed to provide accurate, controlled vacuum that you can see and adjust. 1/4" NPT fittings

Vacuum Reservoir RB 451 is designed to collect excess resin during the infusion process and prevent damage to your vacuum pump. 2.5 gallon tank siz...

A "through the vacuum bag" connector that allows you to easily pull vacuum. Work jointly with our AQD 500 quick disconnect. 1/4" NPT Thread Fitting...

Used to connect polyethylene tubing and/or spiral wrap together, to make your network of vacuum infusion lines to the laminate. "Barbed" ends enabl...

Used to connect polyethylene tubing and/or spiral wrap together, to make your network of vacuum infusion lines to the laminate. "Barbed" ends enabl...

Used to connect polyethylene tubing and/or spiral wrap together, to make your network of vacuum infusion lines to the laminate. "Barbed" ends enabl...

Polyethylene Tubing is used to connect the vacuum reservoir to the part to be infused. Available with a 1/2" O.D. and a 3/8" I.D. for use with 3/8"...

Resinflow 60 is designed to assist resin flow through your part during the VARTM (Vacuum Assisted Resin Transfer Moulding) process. This material i...